Filters

Secure Checkout
Your Shopping Cart Is Empty

Secure Checkout

CODE: 14025 WJ 8" ROCK-LINK PRO Long Arm Lift Kit


WJ 8" ROCK-LINK PRO Long Arm Lift Kit
Purchase WJ 8" ROCK-LINK PRO Long Arm Lift Kit
  • CODE: 14025 WJ 8" ROCK-LINK PRO Long Arm Lift Kit

  • Kit Loading

  • Kit Products

    Choose Your Shocks *

      Choose Your Track Bar *


      ***BILSTEIN SHOCKS ARE IN LIMITED SUPPLY.  BACKORDERS MAY OCCUR.***


      Simply the BEST WJ lift kit available anywhere now available up to 8" of lift! Excellent ride quality on the road, and incredible off road performance. Our kit rides so well, you might even forget you're driving a lifted vehicle. More suspension articulation equates to more traction even without locking differentials and this kit delivers the flex you need.

      Performance and durability are both key factors in the design of this suspension system. You won't have to ever worry about bending these control arms because they are made from 2" x 5/16" wall DOM tubing with a LIFETIME WARRANTY! All mounting bracketry is precision laser cut from 1/4" and 5/16" steel plate. You will not believe the performance gains for yourself until you get on your favorite trail where you didn't have the traction available to get through. Imagine a 34" Super Swamper 6 or 8 inches below the rocker panel* at full suspension droop as your suspension melts to the trail! Yes, your WJ can become a very, VERY capable trail rig with this kit. 

      Take your family and friends with you without the embarrassingly rough ride of many tall lift kits out there. Your highway ride will be a dream come true with this kit. The long front and rear control arms keep the suspension geometry much closer to stock for an impressively smooth ride at 8 inches of lift. Add an Addco rear sway bar and the WJ will ride BETTER than stock!!

      We use an exclusive, non-binding, 3 link setup up front that has a trio of front long arms, and a 4 link rear that will flex more than you thought possible. The bushings at the unibody are greasable and pivot to allow as much suspension travel as the shocks of your choice will allow. Iron Rock Off Road knows your WJ is an investment so we designed our kit with that in mind. What this means is, as always,this kit is 100% bolt on! NO WELDING* and only minor drilling and exhaust modification is required for installation. Tons of adjustment is built in to each link for you to be able to dial your suspension perfectly to your application.  

      INCLUDES:

      • Front 3 link long arm system
      • Front long arm subframe assembly
      • Rear upper/lower triangulated 4-link long arms
      • Rear long arm mounting subframe with nut plates and fasteners
      • Front and rear 8" coil springs
      • Front and rear coil spring retainers
      • Front and rear Trail Tamer shocks
      • Transfer Case drop kit
      • Front adjustable length heavy duty track bar
      • IRO sway bar disconnects
      • Brake line relocating brackets
      • Extended rear sway bar links
      • Track Bar Drop Bracket
      • Drop Pitman Arm


      NOTES:

    • If your transfer case is an NP242WJH (32 spline) and your rear drive shaft is equipped with a harmonic balancer. Additional parts may be required. 
    • This suspension lift kit requires a front double cardan driveshaft. This kit may require a longer front and/or longer rear driveshaft to eliminate driveshaft vibration and maintain adequate slip engagement. 
    • Due to the tall lift height of this suspension kit your OEM driveshafts might not be long enough. Driveshaft length depends on many factors such as the engine, transfer case, and rear axle that your Jeep is equipped with as well as tire size and your desired wheel base. Some WJ OEM driveshafts will work with this kit if the wheel base isn’t stretched too far. The OEM double cardan front driveshaft and OEM rear driveshaft worked on our test WJ: 4.7L, 247 t-case, D30, D44HD, 33” tires, 8” springs, and trimmed fenders.
    • Ensure your rear driveshaft has adequate engagement in the transfer case by marking the slip yoke then remove the drive shaft and measure the amount of engagement. Minimum 50% of slip length should be engaged in transfer case. 
    • To help eliminate drivetrain vibration, it is recommended that the engine and transmission mounts be replaced if they are worn or if they are allowing the engine and transmission to sag. Excessive movement in worn engine and transmission mounts has been known to cause vibration under acceleration with tall lift kits.
    • Contact Iron Rock Off Road with any questions before, during, or after installation.1-877-919-JEEP1-952-210-7185
    • Front 3-link crossmember does not work with CRD models due to a different transmission mount.  Modification may be possible but has not been tested and will not be covered by warranty.
    • Recommended tire size: 33"x11.50" – or metric equivalent

      Recommended wheel backspacing: 4.5"
      TRIMMING MAY BE REQUIRED
      Larger tire sizes possible with bumper/fender trimming and/or extended bump stops.

      Estimated Installation Time: 18-20hrs

      Difficulty Level: 3


      Difficulty Legend

      1 - Kit includes basic components.

      2 - Kit includes little to no adjustable components.

      3 - Kit includes many adjustable components; may require drilling/cutting.

      4 - Kit includes many adjustable components; requires welding; may require drilling/cutting.


      NOTE - Labor Time and Difficulty Level assumes vehicle and/or hardware is in good condition.

      Customer Ratings & Reviews

      1
      Ratings Snapshot
      5.0
      out of 5
      5 (1)
      4 (0)
      3 (0)
      2 (0)
      1 (0)
      Value 5.0
      Quality 5.0
      Service 5.0
      Would recommend this product.
      100%
      5.0
      out of 5
      5 (1)
      4 (0)
      3 (0)
      2 (0)
      1 (0)
      Value 5.0
      Quality 5.0
      Service 5.0
      Would recommend this product.
      100%
      1 Total Reviews
      Real flex performance and superb road handeling
      5 out of 5
      Fix Break Repeat
      Location: Gilbert, AZ
      Date: November 10, 2019
      I have this installed a week ago on my 04 WJ 4.7L, Using 247 NPG Xfer case, Nitto 35's on 17 Wheels. Definitely custom length longer drive shaft for rear if using 35's. OEM DC front drive shaft seems to work with no issues. Ride was real bad, with OEM rear drive shaft on 35's but once lengthened by 2", it worked out perfect and ride was super smooth. Get the front spring retainers, this lift kit really over flexes. So far, really superb performance. No complaints. I didn't bother using a rear sway bar on this ether and my WJ rides perfect and it handles perfect on streets, and Freeway. No DW or any other issues. I ordered the Bilstein shocks also. So far perfect performance.
      Recommended
      Value 5
      Quality 5
      Service 5
      1 Total Reviews
      Prop 65 Warning: CALIFORNIA WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov